Working Voltage | 208 - 240 V AC, 50/60Hz, Single Phase
|
Max. Power Consumption | 4 KW ( 30A Air breaker required ) |
Max. Coating Width | 250mm |
Thickness adjustable range | 0-5mm
|
Coating thickness (after drying) | 30 - 200um (for most kinds of battery electrode coating material) Note: The dried coating thickness results vary depending on the physical property of the coating material.
|
Thickness Precision | ± 3µm (± 5µm at edges)
|
Coating Speed | 0-750 mm / minute |
Max. Drying Temperature
| 120°C ( Using a 240V transformer, can reach 150°C max.) |
Temperature Accuracy | ±1°C |
Heating Zone Length | 710mm (28") |
Reeling/Unreeling Shaft
| 75mm (ID) |
Max. Reeling/Unreeling Diameter | 250mm (OD)
|
Max. Coating Length
| - Depending on the coating and substrate thickness.
- Typically, 10um thick foil with 100um coating can get 600 meters of electrode length coated per run
|
Coating Modes
| - Using transfer coating technique ( Reverse comma ) for better uniformity ( Click Pic below -left for detail )
- Two available coating modes selectable on the control panel.
- Continuous mode
- Intermittent coating ( system performs coating, stops, coats again and so on. The length of the coating and break segments can be specified by the user ).
|
Slurry Stirring
| SS316 Moving Rod
|
Exhaust Port Size | 127mm O.D |
Compressed Air | 0.5-0.8 MPa (Air compressor not included. Please click here to order) Attention: If a gas cylinder is used instead of air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn the installation of a gas regulator. pic1 pic2
|
Optional
| - You may order Dual-Filtration System for NMP Vapor and connect it to the coating system for keeping environmental healthy. Please click Pic.1 for details.
- Atmosphere plasma cleaning add-on for the substrate is available upon request. Such a surface treatment will activate and increase the energy of the substrate surface and thus enables a better adhesion & bonding to the coating materials. Please click Pic.2~3 and Video.1 for more details.
Pic.1 Pic.2 Pic.3 Video.1
- Test the flexibility of the coated electrode with EQ-MBT-12-LD mandrel bending tester. ( Click pic.4 in below for detail.)
- You may use Precision Peristaltic Slurry Feeding Pump for continuous slurry delivery during the roll to roll coating process.( Click Pic.5 & Pic.6 in below to order )
- You may order the Magnetic De-ironing Filtration system (Pic.7) for optimizing the battery electrode slurry condition before the coating process.
Pic.4 Pic.5 Pic.6 Pic.7
|
Product Dimensions | 1620mm ( L) x 950mm (W) x 1100mm (H)
|
Compliance | - CE Certified
- NRTL (UL61010) or CSA certification is available upon request at extra cost.
|
Warranty | - One Year limited warranty with lifetime support
- Rusting and damage due to improper storage condition or maintenance are not covered by warranty
|
Operation Manual & Video | |
Application Notes | - Please use Acetone to clean and dry the doctor blade, slurry feeder, and roller to avoid rusting
- Please contact us for compatibility of slurry solvent and rubber roller of the coater.
- Customers are welcome to visit our facility to receive technical training before shipping of equipment (Please schedule an appointment with us in advance)
- On-site Training is available for customers at extra cost.
- Test the flexibility of the coated electrode with EQ-MBT-12-LD mandrel bending tester. ( Click pic.1 below for detail.)
- PET Film with single side Si Coating is available for Roll-to-Roll tape /slot die/ Micro Gravour casting of Li- ion battery electrode slurry, ceramic, functional resin, ink, and others. Please click the Pic.2 in below to view the product.
Pic.1 Pic.2 |
Net Weight | 1000 kg (2200 lbs) |
Shipping Dimension | 70" x 45" x 55" |